Crunk
03-14-2006, 11:21 AM
This is the first true “Pro” Edition Ego. It has been designed from the ground up to be the lightest, tightest Ego ever produced. This is the Integra Type R or M3CSL equivalent of the Ego 06, where almost every component has been optimized for performance, weight, balance and size.
The attention to detail is unparalleled on any previous Ego. For example, the front regulator mount is 2mm smaller in diameter, just to shave off extra grams. The in-line regulator is devoid of sculpted finger grooves in order to make the body as thin as possible and yet retain structural integrity. The new swivel in-line reg now has a shorter bottom piece in order to have a longer and larger down-stream regulated volume without increasing weight.
On the frame, the rail has been cut down to the bare minimum; to reduce overall gun height, as well as save weight. The new On/Off purge system now mounts so that it butts right up to the bottom of the grips. The frame also shaves off the weight by reducing the thickness of the guard, reducing the profiling of the snatch grip area, removing more metal from inside the upper section of the trigger guard, removing metal from the inside of the frame where it wasn’t necessary, and also deleting the magnetic return mechanism, as the choice of the Pros is spring only trigger return. A larger, flatter trigger makes the marker more responsive by being lighter, with a profile that makes it more comfortable to shoot with more varied hand positions and placements.
Inside the frame there is the Ego 6 circuit board with 3 ramp modes, capped and un-capped semi, as well as an uncapped training mode. The new Ego 6 debounce settings make the marker quicker to shoot and easier to set up than any of the 2005 software versions.
The body is machined all over using complex 3D surface machining to get the weight down to the bare minimum, yet retain the classic flowing Eclipse lines. This is by-far the lightest body Eclipse has created - for any marker.
A new bolt system incorporating no retaining screw, an aluminium plunger, smaller spring and a stainless pin reduces mass in both the cycling system and the overall marker, is open-faced and has a slotted inlet for high flow. It helps reduce cyclic kick and blends seamlessly with the read of the gun. No protruding bolt parts make the sides of the marker easier to clean after a side-shot.
The new C-Lever clamping feed, XSV machined logo, wasted-down front cap, 2-piece shaft and an exclusive XSV navigation console and boot-up screen round out this complete package.
Crucially the SL66 is 14% lighter than a stock Ego 6, and 0.2” shorter in height.
SPECS:
NEW - Exclusive Light-Weight Parts to SL66:
SL66 Frame
SL66 Trigger
SL66 Front Cap
SL66 On/off purge
SL66 Front Regulator Mount
SL66 Swivel In-Line Regulator
SL66 Front LPR Cap
SL66 Bolt
SL66 XSV Machined Body
SL66 XSV Navigation Console
http://www.planeteclipse.com/folders/galleries/sl66_xsv/2grey.jpg
Other Parts:
Nexus Style Eye Covers
Ego 6 Board
6 Firing Modes
Shaft 2-piece Barrel
C-Lever Clamping Feed
And junkie said I wasnt up on the new stuff.
thoughts?
I love it cant wait till I can get my hands on one!
Crunk
The attention to detail is unparalleled on any previous Ego. For example, the front regulator mount is 2mm smaller in diameter, just to shave off extra grams. The in-line regulator is devoid of sculpted finger grooves in order to make the body as thin as possible and yet retain structural integrity. The new swivel in-line reg now has a shorter bottom piece in order to have a longer and larger down-stream regulated volume without increasing weight.
On the frame, the rail has been cut down to the bare minimum; to reduce overall gun height, as well as save weight. The new On/Off purge system now mounts so that it butts right up to the bottom of the grips. The frame also shaves off the weight by reducing the thickness of the guard, reducing the profiling of the snatch grip area, removing more metal from inside the upper section of the trigger guard, removing metal from the inside of the frame where it wasn’t necessary, and also deleting the magnetic return mechanism, as the choice of the Pros is spring only trigger return. A larger, flatter trigger makes the marker more responsive by being lighter, with a profile that makes it more comfortable to shoot with more varied hand positions and placements.
Inside the frame there is the Ego 6 circuit board with 3 ramp modes, capped and un-capped semi, as well as an uncapped training mode. The new Ego 6 debounce settings make the marker quicker to shoot and easier to set up than any of the 2005 software versions.
The body is machined all over using complex 3D surface machining to get the weight down to the bare minimum, yet retain the classic flowing Eclipse lines. This is by-far the lightest body Eclipse has created - for any marker.
A new bolt system incorporating no retaining screw, an aluminium plunger, smaller spring and a stainless pin reduces mass in both the cycling system and the overall marker, is open-faced and has a slotted inlet for high flow. It helps reduce cyclic kick and blends seamlessly with the read of the gun. No protruding bolt parts make the sides of the marker easier to clean after a side-shot.
The new C-Lever clamping feed, XSV machined logo, wasted-down front cap, 2-piece shaft and an exclusive XSV navigation console and boot-up screen round out this complete package.
Crucially the SL66 is 14% lighter than a stock Ego 6, and 0.2” shorter in height.
SPECS:
NEW - Exclusive Light-Weight Parts to SL66:
SL66 Frame
SL66 Trigger
SL66 Front Cap
SL66 On/off purge
SL66 Front Regulator Mount
SL66 Swivel In-Line Regulator
SL66 Front LPR Cap
SL66 Bolt
SL66 XSV Machined Body
SL66 XSV Navigation Console
http://www.planeteclipse.com/folders/galleries/sl66_xsv/2grey.jpg
Other Parts:
Nexus Style Eye Covers
Ego 6 Board
6 Firing Modes
Shaft 2-piece Barrel
C-Lever Clamping Feed
And junkie said I wasnt up on the new stuff.
thoughts?
I love it cant wait till I can get my hands on one!
Crunk